Automatic DB 5801 Manual de usuario descargar pdf (Pagina 1)

Conditions of Sale

STANDARD: Seller’s standard conditions of sale

set forth in Price Sheet 150 apply, except as modified

by the “SPECIAL WARRANTY PROVISIONS,” and

“WARRANTY QUALIFICATIONS” sections in this specifi-

cation bulletin.

SPECIAL TO THIS PRODUCT:

INCLUSIONS: S&C 6801 Automatic Switch Controls

combine sophisticated automatic control schemes with

RTU functionality, data logging, and advanced communi-

cation capabilities in a single package. Models are avail-

able for outdoor pole and pad mounting. 6801 Controls

manage distribution switches and can automatically sec-

tionalize a feeder based on factors such as overcurrent,

loss of voltage, and phase unbalance. One control can

automate one switch, and multiple controls can be pro-

grammed to communicate with each other using the

optional Intelli-Team

 SG Automatic Restoration

System.

The IntelliTeam SG Automatic Restoration System

allows multiple switch controls to work together in teams,

using peer-to-peer communication, and quickly transfer

load to minimize the number of customers affected by a

fault or outage. The system uses distributed intelligence;

no central processing or SCADA is required (though fully

supported). Different types of switches, reclosers, and

controls can be included in the same team.

Utility personnel can communicate with 6801 Controls

to identify and isolate faults and restore service—with or

without a SCADA master station. DNP 3.0 is the supported

protocol, and two S&C approved radios can be installed

inside the enclosure, one for an automation network and

one as a SCADA getaway radio. An S&C SpeedNet™ Radio,

S&C IntelliCom

Mesh Radio, or a fiber-optic modem are

the recommended communication devices for use with

IntelliTeam SG.

6801 Controls provide true RMS voltage and

current readings. Over the operating temperature range

of -40° F to 158° F, current readings are accurate to ±0.5%

full scale, with a resolution of 1 ampere, RMS; voltage

readings are accurate to ±0.5% full scale, with a resolution

of 0.1 Vac. Phase angle readings are accurate to ±1° at

5% of full-scale current, with a resolution of ⅛°. The switch

controls have a current sensor input range of 0 to 800

amperes, RMS.

6801 Controls are configured specifically for fault detec-

tion. Over the overcurrent fault detection range of 0 to

4000 amperes, RMS, overcurrent readings are accurate

to ±0.5% full scale, with a resolution of 1 ampere, RMS.

6801 Controls have extensive data logging capabilities.

Voltage, current, and kVARs are logged every 15 minutes

for one month; daily maximum and minimum voltage, cur-

rent, kVARs, and power factor are logged for one year.

Overcurrent, loss-of-voltage, and fault magnitude and

duration data, as well as equipment diagnostics are also

recorded. A crystal-controlled, temperature-compensated

clock (GPS is optional) provides accurate time-stamping

of the data. The information collected at the switch loca-

tion is invaluable for analyzing problems on the circuit,

troubleshooting, optimizing performance of the installa-

tion, and planning for future requirements. With Intelli-

Team SG-equipped controls, data logging is especially

useful for determining the sequence of events during a

team reconfiguration, and for comparing the information

with substation data.

A PC operating under Windows® XP can be connected

via a DB9, or USB faceplate connector and IntelliLink®

Setup Software used to view real-time data, manage set

points, troubleshoot, and download historical data for

reports. Set points and data can also be accessed remotely

using S&C’s WinMon

Graphical User Interface, or Intelli-

Link

Remote Setup Software.

6801 Controls utilize a single power supply and

battery, eliminating the problems inherent in controls with

multiple power supplies and batteries. This highly efficient

power supply delivers 12 Vdc to the entire system, and

supplies 24-Vdc temperature-compensated battery charg-

ing and float charging to maximize battery life. Battery

condition is periodically checked under varying loads.

Detailed information on battery and power supply status

is available at the faceplate liquid-crystal display and is

accessible at remote locations in communication-device-

equipped controls. 6801 Controls for use with S&C switch-

ing devices can accept control power from a 100- to 140-Vac

or 200- to 280-Vac source, or S&C sensor outputs. If both ac

and sensor sources are available, the control automatically

uses control power and switches to sensor power if control

power is lost.

Automatic Sectionalizing

6801 Controls have automatic sectionalizing capabilities

that can improve circuit reliability when coordinated with

source-side reclosing devices. The controls can help

reduce loss of service and locate faulted line sections. Con-

trols equipped with IntelliTeam SG automatic circuit

reconfiguration can provide full restoration of unaffected

customer loads, if circuit capacity will allow it.

S&C 6801 Automatic Switch Controls

May 18, 2015

Specification Bulletin 1045-31

Specications

1 2 3 4 5 6 ... 10 11

Indice de contenidos

Pagina 1 - Specications

Conditions of Sale STANDARD: Seller’s standard conditions of sale set forth in Price Sheet 150 apply, except as modified by the “SPECIAL WARRANTY P

Pagina 2 - How to Order

① Only available for 5801 Automatic Switch Controls with Suffix “-F01,” for use with Scada-Mate Switches or Scada-Mate CX Switches, or Suffix “-F02,”

Pagina 3

6801 Automatic Switch ControlDimensions in inchesS&C 6801 Automatic Switch ControlsS&C Specication Bulletin 1045-31 11

Pagina 4 - Optional Software

Shots to LockoutThe selectable shots-to-lockout feature prevents the source-side protective device from reclosing into a fault multiple times. Loss of

Pagina 5 - TABLE CONTINUED ▶

6801 Automatic Switch ControlsItem①Control SourceNumber of SwitchingDevices ControlledCatalog NumberBasic With GPS Module②6801 Automatic Switch Contro

Pagina 6 - Options—Continued

Mounting—Must Be SpecifiedMountingSuffix to Be Added to Switch Control Catalog NumberNo Enclosure-JB0▲Pole Mounting, in Padlockable Corrosion-Resista

Pagina 7

TABLE CONTINUED ▶① Total maximum continuous power is 12 watts. This is the available power for all communication equipment installed in the switch con

Pagina 8

① Total maximum continuous power is 12 watts. This is the available power for all communication equipment installed in the switch control. A maximum p

Pagina 9 - Accessories

① Use only with IntelliCom DA Mesh Radio Suffixes “-R201” and “-R203.”★ Radio power is restricted when using control power from three voltage senso

Pagina 10 - Voltage Phase Change Harness

TABLE CONTINUED ▶▲ Specify the appropriate catalog number suffix based on the frequency band range and application for the radio, from the following

Pagina 11 - 6801 Automatic Switch Control

① Use GPS Antenna, Surface Mount Catalog Number 007-001615-01 or Pole-Mounted Antenna Kit for GPS Catalog Number 903-002344-01.② Sixnet SLX-5ES-1 ha

Mas documentos para Herramientas Eléctricas Automatic DB 5801

a Ver el documento Automatic DB 5801 Manual de usuario

Automatic DB 5801 Manual de usuario (12 paginas)

a Ver el documento Automatic DB 5801 Manual de instrucciones

Automatic DB 5801 Manual de instrucciones (13 paginas)

Automatic DB 5801 Manual de usuario (5 paginas)

Comentarios a estos manuales

Sin comentarios

Automatic DB 5801 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Herramientas Eléctricas Automatic DB 5801. Specification Bulletin 1045-31 Manual de usuario

Indice de contenidos

Mas documentos para Herramientas Eléctricas Automatic DB 5801

Comentarios a estos manuales

Automatic DB 5801 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Herramientas Eléctricas Automatic DB 5801. Specification Bulletin 1045-31 Manual de usuario

Indice de contenidos

Mas documentos para Herramientas Eléctricas Automatic DB 5801

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Eléctricas Automatic DB 5801